clamps

Hendrik is the Chief Key Account Officer at STAUFF Corporation. STAUFF offers pipe and hose clamps, hydraulic reservoir accessories, filtration products, diagnostic equipment, and many other products. Today, we invited Hendrik into our forum to learn about STAUFF's clamps and the ways they help with the reduction of noise.

Connect with Hendrik: h.schmuecker@stauff.com 

Connect with the host, Eric Lanke, at elanke@nfpa.com or on LinkedIn at the National Fluid Power Association.

NRC Clamp Testing Video

 

Listen as Paul Abernathy, CEO, and Founder of Electrical Code Academy, Inc. the leading electrical educator in the country, as he answers more questions from the Let’s Ask Paul Portal over at www.PaulAbernathy.com.

In this episode, Paul will tackle the questions submitted by a listener. The topics covered in this episode are about single gang nail-ups and if those are tabs or clamps. While the debate has caused quite a few thousand clicks on Tik Tok and Facebook, the real question is how to address them. In this episode we discuss that topic.

If you are looking to learn more about the National Electrical Code, for electrical exam preparation, or to better your knowledge of the NEC then visits https://fasttraxsystem.com for all the electrical code training you will ever need by the leading electrical educator in the country with the best NEC learning program on the planet.

Listen as Paul Abernathy, CEO, and Founder of Electrical Code Academy, Inc. the leading electrical educator in the country, as he answers more questions from the Let’s Ask Paul Portal over at www.PaulAbernathy.com.

In this episode, Paul will tackle the questions submitted by a listener. The topics covered in this episode are about single gang nail-ups and if those are tabs or clamps. While the debate has caused quite a few thousand clicks on Tik Tok and Facebook, the real question is how to address them. In this episode we discuss that topic.

If you are looking to learn more about the National Electrical Code, for electrical exam preparation, or to better your knowledge of the NEC then visits https://fasttraxsystem.com for all the electrical code training you will ever need by the leading electrical educator in the country with the best NEC learning program on the planet.

CNC Router Tips Podcast Season 2 Episode 69: Hold it Right There.

Hold It Right There: CNC Router Tips Podcast Episode 69 Season 2: CNCRT69S2

How will you hold it, right there? In episode 69 of the CNC Router Tips podcast, host Bill Griggs examines Work holding solutions for CNC Router Tables. How you hold your work piece securely to the work table is crucial to your success. Hold It there fast and secure for repeatability.

There are many types of workholding solutions used with CNC Router tables. These solutions include the following:

• Vises: Vises are a versatile workholding option that can clamp workpieces of varying sizes and shapes. They come in various configurations, including standard vises, multi-axis vises, and self-centering vises.
• Clamps: Clamps are a simple and effective workholding solution that can be used to secure workpieces to the CNC router table. They come in different sizes and shapes, such as C-clamps, toggle clamps, and screw clamps.
• Vacuum Tables: Vacuum tables use suction to hold workpieces in place, providing a secure grip without the need for clamps or vises. They are ideal for holding thin or irregularly shaped workpieces and can be customized to fit specific job requirements.
• T-Slot Tables: T-slot tables have a series of slots that allow for the use of T-nuts, which can be used to secure workpieces in place. They are versatile and can accommodate a wide range of workpiece sizes and shapes.
• Fixture Plates: Fixture plates are used to hold multiple workpieces at once, increasing efficiency and productivity. They are typically made of aluminum or steel and can be customized with various hole patterns and clamping options.
• Collet Chucks: Collet chucks are used to hold round or cylindrical workpieces securely in place. They come in various sizes and can be used with different types of collets, including spring collets and dead-length collets.
• Pallet Systems: Pallet systems allow for quick and easy workpiece changes, reducing downtime and increasing efficiency. They consist of a series of pallets that can be loaded with workpieces off the machine, allowing for continuous machining operations.
• Painters Tape and CA Glue provide a surprisingly strong bond that will hold a workpiece to the spoil board.

Live broadcast and free PDF. Register for CNC Side Hustle Roadmap Wednesday March 15, 2023 at 5:00PM Eastern https://cncroutertips.com/roadmap

Bill Griggs contact info:
Twitter: @BillGriggs
Website: https://www.cncroutertips.com
SHOW NOTES: https://www.cncroutertips.com/69s2

Key takeaways:

• Workholding is essential for CNC router Table success.
• Holding multiple parts is more efficient than machining one parts at a time.
• Fixture plates can make work setup easier and more repeatable.
• Vacuum Tables are widely used to hold large parts.
• Give Painters tape and CA Glue a try.
• Live broadcast and free PDF. Register for CNC Side Hustle Roadmap Wednesday March 15, 2023 at 5:00PM Eastern https://cncroutertips.com/roadmap

WEBSITES MENTIONED

Disclosure: Please note that some of the links below are affiliate links, and at no additional cost to you, I will earn a commission if you decide to make a purchase. Please understand that I have experience with all of these companies, books, tools and I recommend them because they are helpful and useful, not because of the small commissions I make if you decide to buy something. Please do not spend any money on these products unless you feel you need them or that they will help you achieve your goals.



CNC Side Hustle Roadmap https://cncroutertips.com/roadmap
Saunders Machine Works https://saundersmachineworks.com/
Mitee-Bite https://www.miteebite.com/
The Makers Guide http://themakersguide.com
#CNC Router Tips https://www.facebook.com/groups/cncroutertips/
Mach3 Software http://www.themakersguide.com/home/products/mach3
CNC Starter Bit set http://cncroutertips.com/bits
VCarve Demo Video http://cncroutertips.com/demo
VCarve Software http://themakersguide.com/vcarve8
Triple Edge Finder http://themakersguide.com
Maker Masters http://makermasters.com
Resources http://cncroutertips.com/resources
Youtube https://www.youtube.com/c/BillGriggs/featured Bill Griggs contact info:
Twitter: @BillGriggs
Website: http://www.cncroutertips.com
SHOW NOTES: http://www.cncroutertips.com/69S2

Destiny of Manufacturing EP 0221 Jeff Aznavorian -Clips and Clamps

President Clips and Clamps

Leader Precision Metalforming Association

Thought leader in manufacturing 

 

CNCRT 58: Adventures In Work Holding
CNC Router Tips Podcast Episode 58

Work holding is always an adventure for CNC Router Tables. In this episode of CNC Router Tips Bill Griggs tells you about his adventures in work holding.

We discuss the many types of work holding solutions from T-Track extrusion and clamps, double sided tape, modular plates, pallets systems, vacuum tables, Painters tape and instant glue, toggle clamps, eccentric clamps, vise, soft jaws and more.

If you can't hold your work piece securely you can not make a good finished part. We often spend more time figuring out how to hold the work piece than we do actually machining the piece.

In this episode we talk about many of the most popular CNC work holding strategies to help you conquer your adventures in work holding.



Bill Griggs contact info:
Twitter: @BillGriggs
Website: http://cncroutertips.com
SHOW NOTES: http://cncroutertips.com/58
Adventures In Work Holding


WEBSITES MENTIONED

The Makers Guide http://themakersguide.com
#CNC Router Tips https://www.facebook.com/groups/cncroutertips/

CNC Zone http://www.cnczone.com
Youtube http://youtube.com
Shars Tool Company http://www.shars.com
Saundersmachineworks http://saundersmachineworks.com/
Pierson Workholding http://www.piersonworkholding.com/
Mitee Bite https://www.miteebite.com/
8020 Garage Sale http://stores.ebay.com/8020-Inc-Garage-Sale
The Makers Guide http://themakersguide.com
Mach3 Software http://www.themakersguide.com/home/products/mach3
CNC Starter Bit set http://cncroutertips.com/bits
VCarve Demo Video http://cncroutertips.com/demo
VCarve Software http://themakersguide.com/vcarve8
Triple Edge Finder http://themakersguide.com
Maker Masters http://makermasters.com
Resources http://cncroutertips.com/resources

Thanks for listening to episode 90 of the Welding Tips and Tricks Podcast!  For this episode we thought it would be fun to talk about Clamps!  We all know that you can never have too many and always on the search for new ones!  In this episode we chat about the different types of clamps we like to use and the different kinds we would like to have.  This is another deep subject so we really only scratched the surface of this topic but hope that it will help light the fire to start or continue building your personal collection!  Enjoy!  

Pepin & Meader continue HALLOWEEN MONTH with more spooky ghost stories as Meader's sister Sasha drops in to tell her tales of encounters galore!

http://AdamEve.com Enter Offer code MOAN312 to get HALF OFF on the Adam and Eve Weighted Nipple clamps or on just about ANY item. Plus FREE Shipping, a FREE Mystery Gift, and FREE Bonus DVD's.

There's nothing quite like the escalating sensation of a nipple clamp. Add weight and you'll simply explode with pleasure.

Give yourself and your lover an extra special treat.

http://AdamEve.com Enter Offer code MOAN312 to get HALF OFF on the Adam and Eve Weighted Nipple clamps or on just about ANY item. Plus FREE Shipping, a FREE Mystery Gift, and FREE Bonus DVD's.

There's nothing quite like the escalating sensation of a nipple clamp. Add weight and you'll simply explode with pleasure. 

Give yourself and your lover an extra special treat.